轿车底盘铝合金后副车架的压铸技术开发

万里; 刘后尧; 吴树森; 吴湛方; 赖沛基; 张遇朝; 张新强

doi:10.15980/j.tzzz.2012.02.018

压力铸造 | 浏览量 : 0 下载量: 360 CSCD: 4

导出
分享
收藏
专辑

轿车底盘铝合金后副车架的压铸技术开发
Research on Vacuum Die Casting Technology for Al Alloy Chassis Rear Sub-frame of GAC Trumpche Car
2012年32卷第2期页码：145-148
纸质出版日期： 2012 ，
DOI： 10.15980/j.tzzz.2012.02.018

扫描看全文

[1]万里,刘后尧,吴树森,吴湛方,赖沛基,张遇朝,张新强.轿车底盘铝合金后副车架的压铸技术开发[J].特种铸造及有色合金,2012,32(02):145-148.

Wan Li1, Liu Houyao2, Wu Shusen1, et al. Research on Vacuum Die Casting Technology for Al Alloy Chassis Rear Sub-frame of GAC Trumpche Car[J]. Special Casting & Nonferrous Alloys, 2012,32(2):145-148.
[1]万里,刘后尧,吴树森,吴湛方,赖沛基,张遇朝,张新强.轿车底盘铝合金后副车架的压铸技术开发[J].特种铸造及有色合金,2012,32(02):145-148. DOI： 10.15980/j.tzzz.2012.02.018.

Wan Li1, Liu Houyao2, Wu Shusen1, et al. Research on Vacuum Die Casting Technology for Al Alloy Chassis Rear Sub-frame of GAC Trumpche Car[J]. Special Casting & Nonferrous Alloys, 2012,32(2):145-148. DOI： 10.15980/j.tzzz.2012.02.018.

摘要

针对广汽自主品牌"传祺"轿车的底盘铝合金后副车架压铸零件

从压铸合金的力学性能、压铸工艺设计及优化、模具设计及制造、铸件质量控制等方面进行了开发和研究。结果表明

采用耐热密封结构的高真空压铸模具具有良好的密封性能

可靠性高。多区域的温度测量及冷却水流量的实时调节提高了模具温度控制的精度。通过对工艺参数的优化

有效消除了铸件缺陷如裂纹、冷隔、缩孔、缩松等。开发的铝合金后副车架的铸件本体抗拉强度≥240MPa

屈服强度≥145MPa

伸长率≥6%

满足了"传祺"轿车的的使用要求。

Abstract

To meet the requirements of own-brand car named "Trumpche" belonging to Guangzhou Automobile Group （GAC）

high vacuum die-casting technology for the rear sub-frame of car chassis was developed including mechanical properties of the alloy

processing design and optimization

design and manufacturing of the mould

quality control of die castings. The results show that good sealing effect can be improved by adopting high vacuum die casting die with heat resistant sealing structure. Die temperature controlling precision was improved by thermocouple positioned in multi-location of the die and on-time adjustment of cooling water flow rate. Through optimizing processing parameters

some defects

such as crack

cold shut

shrinkage porosity （hole）

can be eliminated. The car chassis with tensile strength over 240 MPa

yield strength over 145 MPa and elongation greater than 6%can be achieved

meeting the use requirements.