真空铸造法制备Cu/AlCoCrFeNi<sub>2.1</sub>复层材料

付莹; 孙婉婷; 孔祥清; 张瑞祥; 李青春; 常国威

doi:10.15980/j.tzzz.2020.09.021

复合材料 | 浏览量 : 0 下载量: 101 CSCD: 0

导出
分享
收藏
专辑

真空铸造法制备Cu/AlCoCrFeNi_2.1复层材料
Preparation of Cladding Cu/AlCoCrFeNi_2.1 Ingot by Continuous Casting
2020年40卷第9期页码：1016-1019
纸质出版日期： 2020 ，
DOI： 10.15980/j.tzzz.2020.09.021

扫描看全文

[1]付莹,孙婉婷,孔祥清,张瑞祥,李青春,常国威.真空铸造法制备Cu/AlCoCrFeNi_(2.1)复层材料[J].特种铸造及有色合金,2020,40(09):1016-1019.

Fu Ying, Sun Wanting, Kong Xiangqing, et al. Preparation of Cladding Cu/AlCoCrFeNi_2.1 Ingot by Continuous Casting[J]. Special Casting & Nonferrous Alloys, 2020,40(9):1016-1019.
[1]付莹,孙婉婷,孔祥清,张瑞祥,李青春,常国威.真空铸造法制备Cu/AlCoCrFeNi_(2.1)复层材料[J].特种铸造及有色合金,2020,40(09):1016-1019. DOI： 10.15980/j.tzzz.2020.09.021.

Fu Ying, Sun Wanting, Kong Xiangqing, et al. Preparation of Cladding Cu/AlCoCrFeNi_2.1 Ingot by Continuous Casting[J]. Special Casting & Nonferrous Alloys, 2020,40(9):1016-1019. DOI： 10.15980/j.tzzz.2020.09.021.

摘要

采用铸造方法制备了Cu/AlCoCrFeNi

2.1

高熵合金复层圆坯

并结合金相显微镜、扫描电镜及力学性能测试等手段

对复层铸锭界面进行了研究。结果表明

所制备的Cu/AlCoCrFeNi

2.1

复层铸坯界面无气孔、夹杂等缺陷

两种合金之间没有明显界面

其结合属于冶金结合。基于扫描电镜对复层铸锭的界面分析

发现Cu侧和AlCoCrFeNi

2.1

侧溶质元素间发生了相互扩散

形成厚度约为0.67μm的扩散层。

Abstract

The cladding Cu/AlCoCrFeNi

2.1

HEAs ingot was prepared by continuous casting.The interface of cladding layer of the Cu/AlCoCrFeNi

2.1

HEAs ingot was investigated by metalloscope

SEM and mechanical performance testing.The results indicate that the interface of cladding Cu/AlCoCrFeNi

2.1

ingot is clean with gas holes and slag free.The absence of interface between the two alloys can be observed

belonging to the metallurgical bonding.The SEM results reveal that the interdiffusion of alloy elements occurs between Cu and HEAs and the diffusion layer is 0.67μm.