激光成形修复K418高温合金的微观组织与硬度

刘建睿; 王猛; 林鑫; 卢鹏辉; 黄卫东

doi:10.15980/j.tzzz.2019.11.008

增材铸造 | 浏览量 : 0 下载量: 169 CSCD: 1

导出
分享
收藏
专辑

激光成形修复K418高温合金的微观组织与硬度
Microstructure and Microhardness of Laser Forming Repaired K418 Superalloy
2019年39卷第11期页码：1187-1192
纸质出版日期： 2019 ，
DOI： 10.15980/j.tzzz.2019.11.008

扫描看全文

[1]刘建睿,王猛,林鑫,卢鹏辉,黄卫东.激光成形修复K418高温合金的微观组织与硬度[J].特种铸造及有色合金,2019,39(11):1187-1192.

Liu Jianrui, Wang Meng, Lin Xin, et al. Microstructure and Microhardness of Laser Forming Repaired K418 Superalloy[J]. Special Casting & Nonferrous Alloys, 2019,39(11):1187-1192.
[1]刘建睿,王猛,林鑫,卢鹏辉,黄卫东.激光成形修复K418高温合金的微观组织与硬度[J].特种铸造及有色合金,2019,39(11):1187-1192. DOI： 10.15980/j.tzzz.2019.11.008.

Liu Jianrui, Wang Meng, Lin Xin, et al. Microstructure and Microhardness of Laser Forming Repaired K418 Superalloy[J]. Special Casting & Nonferrous Alloys, 2019,39(11):1187-1192. DOI： 10.15980/j.tzzz.2019.11.008.

摘要

采用激光立体成形技术对K418合金进行了成形修复

研究了其微观组织与硬度。结果表明

修复K418合金由基体区、热影响区与激光修复区组成

分别由形貌、大小及数量不同的γ-FeCr

0.29

0.16

0.06

基体相、γ′-Ni

Al相及碳化物相组成;铸造基体区与修复区呈紧密的冶金结合

修复区组织呈沉积方向外延生长的柱状晶及连续的层带状结构。在同一沉积层中由于存在粗大树枝晶区与细小树枝晶区而具有不同的硬度。铸造基体区、热影响区与激光修复区的平均硬度值（HV）分别为432.4、499.4、490.6。

Abstract

The microstructure and microhardness of laser forming repaired（LFRed） K418 superalloy were investigated.The results reveal that the LFRed sample can be divided into cast substrate zone（CSZ）

heat-affected zone（HAZ）and laser repaired zone（LRZ）.The microstructures with different morphology

size and number are composed ofγ-FeCr

0.29

0.16

0.06

matrix phases

γ′-Ni

Al phases and MC carbides phases.The LFRed sample presents a compact metallurgical bonding between CZS and LRZ.The LRZ presents columnar dendrites which grew epitaxially along the direction of deposition and a consecutive layer structure.There are difference in microhardness because of difference in grains size at the same deposition layer.The average microhardness of CSZ

HZA and LRZ reach 432.4

499.4 and 490.6HV

respectively.