English Version
实用研究 | 浏览量 : 18 下载量: 99 CSCD: 1
  • 导出

  • 分享

  • 收藏

  • 专辑

    • Ni和Y含量对LPSO结构增强Mg-Ni-Y合金组织及力学性能的影响

    • Effects of Ni and Y Contents on Microstructures and Mechanical Properties of LPSO Structure Reinforced Mg-Ni-Y Alloys

    • 余亮

      1

      杨雄

      2

      吴树森

      2

      汪学阳

      1

      吕书林

      2
    • 2019年39卷第9期 页码:943-946   

      纸质出版日期: 2019

    • DOI: 10.15980/j.tzzz.2019.09.005     

    扫 描 看 全 文

  • 引用

  • [1]余亮,杨雄,吴树森,汪学阳,吕书林.Ni和Y含量对LPSO结构增强Mg-Ni-Y合金组织及力学性能的影响[J].特种铸造及有色合金,2019,39(09):943-946. DOI: 10.15980/j.tzzz.2019.09.005.
    Effects of Ni and Y Contents on Microstructures and Mechanical Properties of LPSO Structure Reinforced Mg-Ni-Y Alloys[J]. Special Casting & Nonferrous Alloys, 2019,39(9):943-946. DOI: 10.15980/j.tzzz.2019.09.005.
  •  
  •  
    论文导航

    摘要

    以长周期堆垛有序(LPSO)结构增强的Mg100-3xNixY2x(x=0.5,1.0,1.5,2.0,摩尔分数,%)合金为对象,研究了Ni和Y含量对合金微观组织和力学性能的影响。结果表明,随着Ni和Y含量增加,合金中的初生α-Mg晶粒变细,LPSO结构的体积分数由10%上升至40%,在Mg94Ni2Y4合金中出现了因Ni过量而产生的共晶Mg2Ni相。合金的强度随着Ni和Y含量的增加而升高,但伸长率持续下降。

    Abstract

    The effects of Ni and Y contents on the microstructure and mechanical properties of Mg100-3xNixY2x(x=0.5,1.0,1.5,2.0%)alloys reinforced with Long Period Stacking Order(LPSO)structure were analyzed.The results show that with the increase of Ni and Y contents,the primaryα-Mg grains in the alloys is refined and the volume fraction of LPSO structure is increased from 10% to 40%.Eutectic Mg2Ni phase exists in Mg94Ni2Y4 alloy due to the excessive Ni element.The tensile strength of the alloys is increased with the increase of Ni and Y contents,while the elongation is decreased continuously.

    关键词

    Mg-Ni-Y合金; LPSO结构; 微观组织; 力学性能

    Keywords

    Mg-Ni-Y Alloys; LPSO Structure; Microstructure; Mechanical Properties

    文章被引用时,请邮件提醒。
    提交

    相关作者

    马振星 太原理工大学材料科学与工程学院
    游志勇 太原理工大学材料科学与工程学院
    蒋傲雪 太原理工大学材料科学与工程学院
    于杰 太原理工大学材料科学与工程学院
    王彬 太原理工大学材料科学与工程学院
    伍德超 合肥工业大学材料科学与工程学院;高性能铜合金材料及成形教育部工程研究中心
    方晓刚 合肥工业大学材料科学与工程学院;高性能铜合金材料及成形教育部工程研究中心;华中科技大学材料成形与模具技术全国重点实验室
    张天阳 合肥工业大学材料科学与工程学院;高性能铜合金材料及成形教育部工程研究中心

    相关机构

    太原理工大学材料科学与工程学院
    合肥工业大学材料科学与工程学院
    高性能铜合金材料及成形教育部工程研究中心
    华中科技大学材料成形与模具技术全国重点实验室
    芜湖瑞鹄汽车轻量化技术有限公司
    0