RE对铸造Al-6Zn-2.5Mg-1.8Cu合金热裂倾向性的影响

马士平; 闫成鑫; 于宝义; 郑黎; 李润霞

doi:10.15980/j.tzzz.2019.03.024

轻有色合金 | 浏览量 : 0 下载量: 84 CSCD: 1

导出
分享
收藏
专辑

RE对铸造Al-6Zn-2.5Mg-1.8Cu合金热裂倾向性的影响
Effects of RE Addition on the Hot Tearing Susceptibility of the Cast Al-6Zn-2.5Mg-1.8Cu Alloys
2019年39卷第3期页码：326-330
纸质出版日期： 2019 ，
DOI： 10.15980/j.tzzz.2019.03.024

扫描看全文

[1]马士平,闫成鑫,于宝义,郑黎,李润霞.RE对铸造Al-6Zn-2.5Mg-1.8Cu合金热裂倾向性的影响[J].特种铸造及有色合金,2019,39(03):326-330.

Ma Shiping, Yan Chengxin, Yu Baoyi, et al. Effects of RE Addition on the Hot Tearing Susceptibility of the Cast Al-6Zn-2.5Mg-1.8Cu Alloys[J]. Special Casting & Nonferrous Alloys, 2019,39(3):326-330.
[1]马士平,闫成鑫,于宝义,郑黎,李润霞.RE对铸造Al-6Zn-2.5Mg-1.8Cu合金热裂倾向性的影响[J].特种铸造及有色合金,2019,39(03):326-330. DOI： 10.15980/j.tzzz.2019.03.024.

Ma Shiping, Yan Chengxin, Yu Baoyi, et al. Effects of RE Addition on the Hot Tearing Susceptibility of the Cast Al-6Zn-2.5Mg-1.8Cu Alloys[J]. Special Casting & Nonferrous Alloys, 2019,39(3):326-330. DOI： 10.15980/j.tzzz.2019.03.024.

摘要

在铸造Al-6Zn-2.5Mg-1.8Cu合金中分别加入0、0.05%、0.1%和0.15%的RE

研究了RE对合金的热裂倾向、微观组织和力学性能的影响。结果表明

RE的加入可细化晶粒尺寸

提高合金的力学性能

降低合金的热裂倾向。在加入范围内

RE含量为0.1%时

热裂倾向性最低

晶粒尺寸最小

力学性能最佳

合金的抗拉强度和伸长率分别为180MPa和3%。

Abstract

Hot tearing susceptibility

microstructures and mechanical properties of cast Al-6Zn-2.5Mg-1.8Cu alloy with RE contents Such as 0

0.05%

0.1% and 0.15% were investigated.The results reveal that RE addition in alloy can refine grain size and improve the mechanical properties as well as decreasing the hot tearing susceptibility of the alloy.The alloy with 0.1%RE has the lowest hot tearing susceptibility

the smallest grain size and the desirable mechanical properties

where tensile strength and elongation of the alloy reach 180 MPa and 3%

respectively.