薄壁铜管游动芯头低频振动拉拔力影响规律

姜志宏; 姜晓锋; 许永强

doi:10.15980/j.tzzz.2019.01.031

重有色合金 | 浏览量 : 0 下载量: 93 CSCD: 1

导出
分享
收藏
专辑

薄壁铜管游动芯头低频振动拉拔力影响规律
Law of Affecting Low-frequency Vibration Pulling Force of Thin-walled Copper Tube Swimming Core
2019年39卷第1期页码：113-116
纸质出版日期： 2019 ，
DOI： 10.15980/j.tzzz.2019.01.031

扫描看全文

[1]姜志宏,姜晓锋,许永强.薄壁铜管游动芯头低频振动拉拔力影响规律[J].特种铸造及有色合金,2019,39(01):113-116.

Jiang Zhihong, Jiang Xiaofeng, Xu Yongqiang. Law of Affecting Low-frequency Vibration Pulling Force of Thin-walled Copper Tube Swimming Core[J]. Special Casting & Nonferrous Alloys, 2019,39(1):113-116.
[1]姜志宏,姜晓锋,许永强.薄壁铜管游动芯头低频振动拉拔力影响规律[J].特种铸造及有色合金,2019,39(01):113-116. DOI： 10.15980/j.tzzz.2019.01.031.

Jiang Zhihong, Jiang Xiaofeng, Xu Yongqiang. Law of Affecting Low-frequency Vibration Pulling Force of Thin-walled Copper Tube Swimming Core[J]. Special Casting & Nonferrous Alloys, 2019,39(1):113-116. DOI： 10.15980/j.tzzz.2019.01.031.

摘要

为准确描述薄壁铜管游动芯头低频振动过程中拉拔力影响因素的变化

借助有限元分析软件MSC.Marc

建立铜管低频振动拉拔模型

分析拉拔速度、激振振幅、激振频率、模具锥角（外模半锥角、芯头半锥角）对拉拔力的影响。结果表明

拉拔速度的增加将引起拉拔力的小幅度增加

在激振频率为80～170Hz范围内拉拔力先减小后增大

激振振幅的增加将引起拉拔力的显著降低

外模半锥角与芯头半锥角存在最佳的模具锥角组合。

Abstract

In order to accurately describe the variation law of the influencing factors of pulling force during the low-frequency vibration of the thin-walled copper tube

the MSC.Marc was used to establish the low-frequency vibration drawing model of the copper tube

and the influence of drawing speed

excitation amplitude

excitation frequency and mold cone angle（the outer mold half cone angle

the core half cone angle）on the drawing force was analyzed.The results show that with the increase of drawing speed

drawing force is increased slightly.In the range of excitation frequency of 80～150 Hz

the pulling force is decreased firstly and then increased.With increasing in excitation amplitude

pulling force is decreased greatly.And outer mold half cone angle and core half cone angle have a best mold cone angle combination.

关键词

薄壁铜管游动芯头拉拔低频振动拉拔力

Keywords

Thin-Walled Copper TubeFloating Core PullLow Frequency VibrationDrawing Force

references

文章被引用时，请邮件提醒。

提交

不同成分铝杆的辊模拉拔工艺设计