基于Simufact的QSn7-0.2衬套强力旋压与变薄拉深的成形精度

李志伟; 樊文欣; 杨锋; 张厚祖; 郭佩剑

doi:10.15980/j.tzzz.2018.10.029

重有色合金 | 浏览量 : 0 下载量: 134 CSCD: 1

导出
分享
收藏
专辑

基于Simufact的QSn7-0.2衬套强力旋压与变薄拉深的成形精度
Forming Accuracy of Power Spinning and Ironing of Tin Bronze Connecting Rod Bushing Based on Finite Element Software
2018年38卷第10期页码：1155-1158
纸质出版日期： 2018 ，
DOI： 10.15980/j.tzzz.2018.10.029

扫描看全文

[1]李志伟,樊文欣,杨锋,张厚祖,郭佩剑.基于Simufact的QSn7-0.2衬套强力旋压与变薄拉深的成形精度[J].特种铸造及有色合金,2018,38(10):1155-1158.

Li Zhiwei, Fan Wenxin, Yang Feng, et al. Forming Accuracy of Power Spinning and Ironing of Tin Bronze Connecting Rod Bushing Based on Finite Element Software[J]. Special Casting & Nonferrous Alloys, 2018,38(10):1155-1158.
[1]李志伟,樊文欣,杨锋,张厚祖,郭佩剑.基于Simufact的QSn7-0.2衬套强力旋压与变薄拉深的成形精度[J].特种铸造及有色合金,2018,38(10):1155-1158. DOI： 10.15980/j.tzzz.2018.10.029.

Li Zhiwei, Fan Wenxin, Yang Feng, et al. Forming Accuracy of Power Spinning and Ironing of Tin Bronze Connecting Rod Bushing Based on Finite Element Software[J]. Special Casting & Nonferrous Alloys, 2018,38(10):1155-1158. DOI： 10.15980/j.tzzz.2018.10.029.

摘要

利用有限元仿真软件Simufact中强力旋压和变薄拉深模块分别对相同的连杆衬套毛坯进行了三旋轮错距强力旋压和3次变薄拉深两种工艺的数值模拟。以连杆衬套的实际外径、内圆度误差和壁厚偏差作为成形精度的评价指标

从而探究三旋轮错距强力旋压和3次变薄拉深两种工艺成形后的成形精度。结果表明

采用3次变薄拉深工艺加工成形后的连杆衬套成形精度略优于三旋轮错距强力旋压

但其强度低于强力旋压后工件的强度[1]。

Abstract

In order to get better quality of tin bronze connecting rod bushing

two modules of power spinning and ironing in Simufact software were used to treat the same tubular blank.The actual outer diameter

internal roundness error and thickness deviation of connection rod bushing after numerical simulation were considered as estimated index in order to research the forming accuracy of the power spinning process of three rotating wheels and the ironing process of three times.The results show that the forming accuracy of the ironing process of three times is higher than that of the power spinning process of three rotating wheels

and the strength after power spinning is higher than that of ones after ironing.