蛇形通道浇注法制备半固态A380铝合金浆料

刘志勇; 毛卫民; 王伟番; 郑志凯

doi:10.15980/j.tzzz.2015.01.014

半固态加工 | 浏览量 : 0 下载量: 134 CSCD: 2

导出
分享
收藏
专辑

蛇形通道浇注法制备半固态A380铝合金浆料
Preparation of Semi-solid A380 Alloy slurry by the Serpentine Channel Pouring
2015年35卷第1期页码：48-51
纸质出版日期： 2015 ，
DOI： 10.15980/j.tzzz.2015.01.014

扫描看全文

[1]刘志勇,毛卫民,王伟番,郑志凯.蛇形通道浇注法制备半固态A380铝合金浆料[J].特种铸造及有色合金,2015,35(01):48-51.

Liu Zhiyong, Mao Weimin, Wang Weipan, et al. Preparation of Semi-solid A380 Alloy slurry by the Serpentine Channel Pouring[J]. Special Casting & Nonferrous Alloys, 2015,35(1):48-51.
[1]刘志勇,毛卫民,王伟番,郑志凯.蛇形通道浇注法制备半固态A380铝合金浆料[J].特种铸造及有色合金,2015,35(01):48-51. DOI： 10.15980/j.tzzz.2015.01.014.

Liu Zhiyong, Mao Weimin, Wang Weipan, et al. Preparation of Semi-solid A380 Alloy slurry by the Serpentine Channel Pouring[J]. Special Casting & Nonferrous Alloys, 2015,35(1):48-51. DOI： 10.15980/j.tzzz.2015.01.014.

摘要

采用石墨质蛇形通道浇注法制备半固态A380铝合金浆料

研究了浇注温度、弯道数量和弯道内径对半固态A380铝合金浆料组织的影响。结果表明

浇注温度在610

50℃范围时可获得理想的半固态A380铝合金浆料

半固态A380铝合金浆料组织随浇注温度的降低

由蔷薇晶组织向近球晶或球晶组织演变。在相同浇注温度条件下

弯道数量的增加或通道内径尺寸的减小都可细化半固态A380铝合金浆料组织中的初生α-Al晶粒

提高形状因子

进而优化其浆料组织。

Abstract

The semi-solid slurry of A380 aluminum alloy was prepared through a serpentine pouring channel

and influences of pouring temperature

the curve numbers and the curve diameters in a serpentine channel on microstructure of the alloy slurry were investigated.The experimental results show that the satisfactory semi-solid A380 aluminum alloy slurry can be obtained with the pouring temperature at 610℃

650 ℃.The microstructure of the semi-solid A380 alloy slurry can be evolved from rossette to spherical particle.At a given pouring temperature

the particle size of primaryα-Al can be decreased and the shape factor of primaryα-Al is increased with the increases of the curve number or decrease of the diameter of the curve

at the same time

the microstructure of semi-solid A380 alloy slurry can be optimized.