加压条件下固-液复合法制备Cu/Al复合材料

张亚; 宋克兴; 刘亚民; 赵培峰; 张彦敏

doi:10.15980/j.tzzz.2014.01.011

复合材料 | 浏览量 : 0 下载量: 132 CSCD: 3

导出
分享
收藏
专辑

加压条件下固-液复合法制备Cu/Al复合材料
Fabrication of Cu/Al Composites by Solid-liquid Bonding Method under Pressure
2014年34卷第1期页码：101-104
纸质出版日期： 2014 ，
DOI： 10.15980/j.tzzz.2014.01.011

扫描看全文

[1]张亚,宋克兴,刘亚民,赵培峰,张彦敏.加压条件下固-液复合法制备Cu/Al复合材料[J].特种铸造及有色合金,2014,34(01):101-104.

Zhang Ya, Song Kexing, Liu Yamin, et al. Fabrication of Cu/Al Composites by Solid-liquid Bonding Method under Pressure[J]. Special Casting & Nonferrous Alloys, 2014,34(1):101-104.
[1]张亚,宋克兴,刘亚民,赵培峰,张彦敏.加压条件下固-液复合法制备Cu/Al复合材料[J].特种铸造及有色合金,2014,34(01):101-104. DOI： 10.15980/j.tzzz.2014.01.011.

Zhang Ya, Song Kexing, Liu Yamin, et al. Fabrication of Cu/Al Composites by Solid-liquid Bonding Method under Pressure[J]. Special Casting & Nonferrous Alloys, 2014,34(1):101-104. DOI： 10.15980/j.tzzz.2014.01.011.

摘要

在加压条件下采用固-液复合法制备了Cu/Al复合材料

并对复合材料界面层的硬度、抗拉强度及微观组织进行了研究。结果表明

在加压条件下固-液复合法可以制备出抗拉强度达38.24 MPa且Cu/Al复合界面结合良好的复合材料;界面层硬度显著高于两侧基体硬度;界面层靠近铜侧区域容易出现断裂现象

生成的脆性相CuAl2是造成复合材料断裂的主要原因之一。

Abstract

Cu/Al composites were fabricated by solid-liquid bonding method under pressure

and the micro-hardness

tensile strength and microstructures of Cu/Al interfaces were investigated by SEM（scanning electron microscope）

micro-hardness tester and tensile testing.The results show that the wellbonded metallurgical bonding interface with tensile strength of 38.24 MPa can be obtained

and the hardness of interface layer is significantly higher than that of matrix.Fracture is easy to appear in the area nearby the copper side

which is attributed to the generation of thhe CuAl2 brittle phase.

关键词

固-液复合Cu/Al复合材料界面层CuAl2

Keywords

Solid-Liquid Bonding MethodCu/Al CompositesInterface LayerCuAl2

references

文章被引用时，请邮件提醒。

提交

工艺参数对液态铝与钢界面层及其性能的影响

铸轧法制备钛铝复合板的界面组织与性能