Al<sub>2</sub>O<sub>3</sub>/Cu复合材料的载流摩擦磨损性能

刘瑞华; 宋克兴; 贾淑果; 郜建新; 国秀花; 李建弘

English Version

复合材料 | 浏览量 : 45 下载量: 144 CSCD: 2

导出
分享给微信好友或者朋友圈

分享
收藏
专辑

Al₂O₃/Cu复合材料的载流摩擦磨损性能
Effects of Speed and Load on Loading Wear and Friction Resistance of Al₂O₃/Cu Composites
- 角色： First author 第一作者
- 机构：
  河南科技大学材料科学与工程学院
刘瑞华
1 ，
- 机构：
  河南科技大学材料科学与工程学院
宋克兴
1 ，
- 机构：
  河南科技大学材料科学与工程学院
贾淑果
1 ，
- 机构：
  河南科技大学材料科学与工程学院
郜建新
1 ，
- 机构：
  河南科技大学材料科学与工程学院
国秀花
1 ，
- 机构：
  河南科技大学材料科学与工程学院
李建弘
1
2007年第12期页码：960-962
纸质出版日期： 2007 ，
DOI：

扫描看全文

引用
[1]刘瑞华,宋克兴,贾淑果,郜建新,国秀花,李建弘.Al_2O_3/Cu复合材料的载流摩擦磨损性能[J].特种铸造及有色合金,2007(12):960-962+901.

Liu Ruihua, Song Kexing, Jia Shuguo, et al. Effects of Speed and Load on Loading Wear and Friction Resistance of Al₂O₃/Cu Composites[J]. Special Casting & Nonferrous Alloys, 2007,(12):960-962.
[1]刘瑞华,宋克兴,贾淑果,郜建新,国秀花,李建弘.Al_2O_3/Cu复合材料的载流摩擦磨损性能[J].特种铸造及有色合金,2007(12):960-962+901. DOI：

Liu Ruihua, Song Kexing, Jia Shuguo, et al. Effects of Speed and Load on Loading Wear and Friction Resistance of Al₂O₃/Cu Composites[J]. Special Casting & Nonferrous Alloys, 2007,(12):960-962. DOI：

摘要

研究了采用内氧化法制备的Al2O3/Cu复合材料在载流条件下的干滑动摩擦磨损性能,结果表明,在相同条件下,Al2O3/Cu复合材料的抗摩擦磨损性能明显优于紫铜;当电流一定时,随着速度与载荷的增加,销试样的磨损率增加,摩擦因数降低。Al2O3/Cu复合材料销试样表层发生了磨粒磨损和粘着磨损,紫铜表层主要发生了粘着磨损。在试验范围内,质量分数为0.60%的Al2O3的Cu基复合材料比质量分数为0.24%的磨损率和摩擦因数低。

译

Abstract

The dry wear and friction resistance of Al₂O₃/Cu composites prepared by internal oxidation method have been examined under the condition of loading.The results revealed that the wear and friction resistance of Al₂O₃/Cu composites are superior to that of red copper under the same condition.The weight loss of the samples is increased and friction factor is decreased with increasing in speed and loading at a given current.The abrasive and adhesion wear are observed in surface of Al₂O₃/Cu composites samples,while the adhesion wear in surface of red copper is generated.The weight loss and friction factor of the Al₂O₃/Cu composites with 0.60% Al₂O₃ content is lower than that of ones with 0.24% Al₂O₃ content under the experimental condition.

译

关键词

Al2O3/Cu复合材料; 摩擦磨损; 磨损率; 摩擦因数; 内氧化

译

Keywords

Al2O3/Cu Composites; Wear and Friction; Weight Loss; Friction Factor; Internal-oxidized Rate

译

摘要

研究了采用内氧化法制备的Al2O3/Cu复合材料在载流条件下的干滑动摩擦磨损性能

结果表明

在相同条件下

Al2O3/Cu复合材料的抗摩擦磨损性能明显优于紫铜;当电流一定时

随着速度与载荷的增加

销试样的磨损率增加

摩擦因数降低。Al2O3/Cu复合材料销试样表层发生了磨粒磨损和粘着磨损

紫铜表层主要发生了粘着磨损。在试验范围内

质量分数为0.60%的Al2O3的Cu基复合材料比质量分数为0.24%的磨损率和摩擦因数低。

Abstract

The dry wear and friction resistance of Al

/Cu composites prepared by internal oxidation method have been examined under the condition of loading.The results revealed that the wear and friction resistance of Al

/Cu composites are superior to that of red copper under the same condition.The weight loss of the samples is increased and friction factor is decreased with increasing in speed and loading at a given current.The abrasive and adhesion wear are observed in surface of Al

/Cu composites samples

while the adhesion wear in surface of red copper is generated.The weight loss and friction factor of the Al

/Cu composites with 0.60% Al

content is lower than that of ones with 0.24% Al

content under the experimental condition.