热处理工艺对高强高导Cu-Cr-Zr系合金性能的影响

姜锋; 陈蒙; 李金龙; 陈小波

重有色合金 | 浏览量 : 0 下载量: 221 CSCD: 1

导出
分享
收藏
专辑

热处理工艺对高强高导Cu-Cr-Zr系合金性能的影响
Effects of Heat Treatment on Properties of High Strength and High Conductivity Cu-Cr-Zr Alloy
2010年30卷第11期页码：1068-1071
纸质出版日期： 2010 ，
DOI：

扫描看全文

[1]姜锋,陈蒙,李金龙,陈小波.热处理工艺对高强高导Cu-Cr-Zr系合金性能的影响[J].特种铸造及有色合金,2010,30(11):1068-1071+979-980.

Effects of Heat Treatment on Properties of High Strength and High Conductivity Cu-Cr-Zr Alloy[J]. Special Casting & Nonferrous Alloys, 2010,30(11):1068-1071.
[1]姜锋,陈蒙,李金龙,陈小波.热处理工艺对高强高导Cu-Cr-Zr系合金性能的影响[J].特种铸造及有色合金,2010,30(11):1068-1071+979-980. DOI：

Effects of Heat Treatment on Properties of High Strength and High Conductivity Cu-Cr-Zr Alloy[J]. Special Casting & Nonferrous Alloys, 2010,30(11):1068-1071. DOI：

摘要

通过金相、透射电镜分析合金的微观结构

采用力学性能测试和电导率测试分析合金的物理性能

研究了热处理工艺对高强高导Cu-0.8Cr-0.2Zr合金性能的影响。通过对固溶-时效

固溶-冷轧-时效

固溶-时效-冷轧-退火3种热处理工艺下合金的强度和电导率进行对比

分析计算出70%冷变形、时效、退火对合金强度的影响为:163、177、-62MPa;对电导率的影响为-15.08、21.75、2.99MS/m。结合试验结果对比分析了合金在各个不同热处理后微观组织和结构的变化对合金力学和导电性能作用。经固溶+冷轧+时效工艺

合金的性能最佳:强度为529MPa

电导率为49.36MS/m

其再结晶温度为520℃。

Abstract

Effects of heat treatment on microstructure and properties of Cu-0.8Cr-0.2Zr alloy were investigated by OM（optical microscope）

TEM（transmission electron microscope）and tensile testing

electrical conductivity measurements.Effects of 70% cold deformation

aging

annealing on strength of the alloy were analyzed by comparing tensile and electrical conductivity in condition of solid solution

solid solution +cold rolling+aging

solid solution+aging+cold rolling+annealling.The results show that effects of strength and electrical conductivity of the alloy after 70% cold deformation

aging and annealing are 163 MPa

177MPa

-162MPa and-15.08MS/m

21.75 MS/m

2.99MS/m

respectively.Strength and electrical conductivity of the alloy treated by solid solution +cold rolling+aging are 529MPa and 49.36MS/m

respectively

meanwhile

recystallization temperature is 520℃.