English Version
复合材料 | 浏览量 : 28 下载量: 159 CSCD: 1
  • 导出

  • 分享

  • 收藏

  • 专辑

    • TiC/Ti3AlC2复合材料的制备及性能研究

    • Preparation and Properties of TiC/Ti3AlC2 Composites

    • 艾桃桃

      1
    • 2011年31卷第4期 页码:360-362   

      纸质出版日期: 2011

    扫 描 看 全 文

  • 引用

  • [1]艾桃桃.TiC/Ti_3AlC_2复合材料的制备及性能研究[J].特种铸造及有色合金,2011,31(04):360-362+398. DOI:
    Ai Taotao. Preparation and Properties of TiC/Ti3AlC2 Composites[J]. Special Casting & Nonferrous Alloys, 2011,31(4):360-362. DOI:
  •  
  •  
    论文导航

    摘要

    利用2TiC-Ti-Al体系的原位放热反应制备TiC/Ti3AlC2复合材料。借助XRD和SEM分析不同合成温度对应产物的相组成和微观结构,并测量其密度和抗压强度。结果表明,随着合成温度的升高,Ti3AlC2含量减小,TiC杂质相含量增大,层状或板状Ti3AlC2组织减少,大颗粒状TiC显著增多。经1350℃烧结后,合成产物中Ti3AlC2含量相对较高,其密度和抗压强度达4.03g/cm3和111.29MPa。

    Abstract

    TiC/Ti3AlC2 composites were prepared by in-situ synthesis in 2TiC-Ti-Al system.Phase constituent and microstructure of the reactive products at different synthesized temperatures were observed by XRD(X-ray diffraction) and SEM(scanning electron microscope),and its density and compressive strength were measured.The results reveal that with increasing in reactive temperature,Ti3AlC2 phase content is decreased and TiC phase content increased,meanwhile,lamellar or layered Ti3AlC2 phase is decreased and larger TiC particle is greatly increased.With sintering at 1350℃,Ti3AlC2 phase content is higher,and density and compressive strength of the composites reach 4.03g/cm3 and 111.29MPa,respectively.

    关键词

    Ti3AlC2; TiC; 制备; 性能

    Keywords

    Ti3AlC2 Phase; TiC Phase; Preparation; Properties

    文章被引用时,请邮件提醒。
    提交

    相关作者

    艾桃桃 陕西理工学院材料科学与工程学院
    冯小明 陕西理工学院材料科学与工程学院
    赵卓玲 陕西理工学院材料科学与工程学院
    胡金宝 沈阳航空航天大学民用航空学院;中国科学院金属研究所
    牟义强 沈阳航空航天大学民用航空学院;中国科学院金属研究所
    徐勤思 沈阳航空航天大学民用航空学院;中国科学院金属研究所
    胡辰煜 沈阳航空航天大学民用航空学院
    李尚达 沈阳航空航天大学民用航空学院

    相关机构

    陕西理工学院材料科学与工程学院
    沈阳航空航天大学民用航空学院
    中国科学院金属研究所
    洛阳双瑞精铸钛业有限公司中国船舶集团有限公司第七二五研究所
      北京科技大学  
    0