Microstructure and Mechanical Properties of Mg-8Zn-1Ag-0.7Zr Alloy

Yu Guokang; He Kai; Qin Shouyi; Sun Minjie; Wang Zhengyuan; Pan Long; Fan Lipeng; Liu Yingzhuo

doi:10.15980/j.tzzz.2020.05.005

Views : 0 下载量: 52 CSCD: 0

Export
Share
Collection
Album

Microstructure and Mechanical Properties of Mg-8Zn-1Ag-0.7Zr Alloy
Vol. 40, Issue 5, Pages: 485-488(2020)
Published： 2020 ，
DOI： 10.15980/j.tzzz.2020.05.005

扫描看全文

[1]余国康,何凯,秦守益,孙敏杰,王征远,潘龙,范李鹏,刘颖卓.Mg-8Zn-1Ag-0.7Zr合金组织和力学性能研究[J].特种铸造及有色合金,2020,40(05):485-488.

Yu Guokang, He Kai, Qin Shouyi, et al. Microstructure and Mechanical Properties of Mg-8Zn-1Ag-0.7Zr Alloy. [J]. Special Casting & Nonferrous Alloys 40(5):485-488(2020)
[1]余国康,何凯,秦守益,孙敏杰,王征远,潘龙,范李鹏,刘颖卓.Mg-8Zn-1Ag-0.7Zr合金组织和力学性能研究[J].特种铸造及有色合金,2020,40(05):485-488. DOI： 10.15980/j.tzzz.2020.05.005.

Yu Guokang, He Kai, Qin Shouyi, et al. Microstructure and Mechanical Properties of Mg-8Zn-1Ag-0.7Zr Alloy. [J]. Special Casting & Nonferrous Alloys 40(5):485-488(2020) DOI： 10.15980/j.tzzz.2020.05.005.

摘要

利用OM、SEM等手段对Mg-8Zn-1Ag-0.7Zr合金的微观组织、析出相成分和力学性能进行了研究

为工程应用提供参考。结果表明

Mg-8Zn-1Ag-0.7Zr合金以等轴晶方式凝固

铸态合金主要由α-Mg、Mg-Zn-Ag三元化合物和Zn

相组成

第二相主要集中分布在晶界上。热处理后

晶界上第二相的连续分布形态得到明显改善

Zn元素在基体中的含量变化明显。铸态时

Zn元素含量为3.09%

经固溶处理后

增加为8.24%。时效处理后

Zn元素含量下降至5.42%

起到很好的析出强化作用。T4态合金的抗拉强度、屈服强度和伸长率分别为311.4 MPa、147.4 MPa和13.7%

较铸态提高明显。经T6处理后

合金抗拉强度、屈服强度和伸长率为325.4 MPa、217.6 MPa和5.1%。

Abstract

The microstructure and mechanical properties of Mg-8 Zn-1 Ag-0.7 Zr alloy were investigated by OM、SEM and tensile testing. The experimental results reveal that the Mg-8 Zn-1 Ag-0.7 Zr alloy is solidified in form of equiaxial crystal

and the as-cast alloy is mainly composed of the α-Mg、Mg-Zn-Ag ternary compound and Zn

phase. The second phase is mainly distributed along the grain boundary. After heat treatment

distribution morphology of secondary phase is improved obviously on the grain boundary. Zn content in the matrix is changed greatly. After solid solution

Zn content in the alloy is increased from 3.09% in as-cast state to 8.24%

while it is decreased to 5.42% after aging treatment

presenting the satisfied precipitate strengthening effects. The tensile strength

yield strength and elongation of the alloy by T4 treatment reach 311.4 MPa

147.4 MPa and 13.7%. After T6 treatment

the tensile strength

yield strength and elongation of the alloy reach 325.4 MPa

217.6 MPa and 5.1%

respectively.