Numerical Simulation and Process Optimization of Sand Casting Aluminum Alloy Cover

Views : 0 下载量: 196 CSCD: 1

Export
Share
Collection
Album

Numerical Simulation and Process Optimization of Sand Casting Aluminum Alloy Cover
Vol. 37, Issue 10, Pages: 1061-1063(2017)
Published： 2017 ，
DOI： 10.15980/j.tzzz.2017.10.005

扫描看全文

[1]姜月明,李屹,丁旭,陈敏,沈刚,吴兵.砂型铸造铝合金盖子数值模拟及工艺优化[J].特种铸造及有色合金,2017,37(10):1061-1063.

Jiang Yueming, Li Yi, Ding Xu, et al. Numerical Simulation and Process Optimization of Sand Casting Aluminum Alloy Cover. [J]. Special Casting & Nonferrous Alloys 37(10):1061-1063(2017)
[1]姜月明,李屹,丁旭,陈敏,沈刚,吴兵.砂型铸造铝合金盖子数值模拟及工艺优化[J].特种铸造及有色合金,2017,37(10):1061-1063. DOI： 10.15980/j.tzzz.2017.10.005.

Jiang Yueming, Li Yi, Ding Xu, et al. Numerical Simulation and Process Optimization of Sand Casting Aluminum Alloy Cover. [J]. Special Casting & Nonferrous Alloys 37(10):1061-1063(2017) DOI： 10.15980/j.tzzz.2017.10.005.

摘要

运用AnyCasting软件对铝合金盖子砂型铸造过程进行模拟

分析了铸件缺陷产生的部位和原因。针对砂型铸造过程中易出现的铸造缺陷

通过改变浇注系统

合理设置冷铁和冒口

同时提高浇注速度

减少了缺陷

提高了铸件品质。

Abstract

The sand casting process of aluminum alloy cover was simulated by AnyCasting

and origination of defects was analyzed.Aiming at the casting defects in the sand casting process

by modifying gating system

setting the cold iron and riser reasonably

and increasing the casting speed

the casting defects can be reduced greatly

and the casting quality can be improved.

关键词

砂型铸造铝合金工艺优化数值模拟

Keywords

Sand CastingAluminum AlloyProcess OptimizationNumerical Simulation

references

Alert me when the article has been cited

提交

相关文章

Numerical Simulation and Process Optimization of Sand Casting Aluminum Alloy Box

Numerical Simulation and Optimization of Gating System for Aluminum Alloy Engine Bracket

Design and Optimization of Die-casting Process for Carburetor Midbody Based on Numerical Simulation

Casting Method Design and Numerical Simulation of Complex Thin-wall Frame Aluminum Castings

Optimization of Low Pressure Casting Process for Aluminum Alloy Transmission Control Housing

相关作者

Li Zhongfang 山东理工大学机械工程学院

Yang Siyi 山东理工大学机械工程学院

Zhou Liming 山东理工大学机械工程学院

An Yukun 山东理工大学机械工程学院

Liu Duo 山东理工大学机械工程学院

Zhang Zhenbo 山东理工大学机械工程学院

Han Jieli 重庆大学机械工程学院 ; 重庆大学机械工程学院重庆市镁合金材料工程技术研究中心

Cao Hanxue 重庆大学机械工程学院 ; 重庆大学机械工程学院重庆市镁合金材料工程技术研究中心

相关机构

School of Mechanical Engineering,Shandong University of Technology

Chongqing Engineering Research Center for Magnesium Alloys,Chongqing University

重庆大学机械工程学院重庆市镁合金材料工程技术研究中心

School of Art and Design,Shenyang Institute of Technology

School of Materials Science and Engineering,Shenyang Institute of Technology

⁰