Effects of Cooling Rate on Microstructure and Properties of Mg-5Zn-1Y-0.6Zr Alloy

Liu Guang; Zhang Zhenzhong; Chen Jian; Zhang Hao; Yin Changhao; Zhang Yeming

Views : 0 下载量: 113 CSCD: 2

Export
Share
Collection
Album

Effects of Cooling Rate on Microstructure and Properties of Mg-5Zn-1Y-0.6Zr Alloy
Vol. 29, Issue 11, Pages: 981-983(2009)
Published： 2009 ，
DOI：

扫描看全文

[1]刘广,张振忠,陈骞,张浩,尹长浩,张少明.冷却速度对Mg-5Zn-1Y-0.6Zr合金组织和性能的影响[J].特种铸造及有色合金,2009,29(11):981-983+973.

Liu Guang, Zhang Zhenzhong, Chen Jian, et al. Effects of Cooling Rate on Microstructure and Properties of Mg-5Zn-1Y-0.6Zr Alloy. [J]. Special Casting & Nonferrous Alloys 29(11):981-983(2009)
[1]刘广,张振忠,陈骞,张浩,尹长浩,张少明.冷却速度对Mg-5Zn-1Y-0.6Zr合金组织和性能的影响[J].特种铸造及有色合金,2009,29(11):981-983+973. DOI：

Liu Guang, Zhang Zhenzhong, Chen Jian, et al. Effects of Cooling Rate on Microstructure and Properties of Mg-5Zn-1Y-0.6Zr Alloy. [J]. Special Casting & Nonferrous Alloys 29(11):981-983(2009) DOI：

摘要

采用快速凝固技术制备Mg-5Zn-1Y-0.6Zr合金

用XRD、SEM、HRTEM、显微硬度测量等分析方法研究其凝固组织和性能。结果表明

合金由α-Mg固溶体、晶界处不连续分布的I（Mg3Zn6Y）准晶相和非晶相组成。根据热传导理论

采用一维傅立叶热传导方程计算了合金的冷却速度。冷却速度的提高使得晶粒细化、成分均匀、非晶相含量增多。硬度（HV）随冷速的提高显著增大

最大值为167.23

是普通凝固合金的2.2倍。

Abstract

The Mg-5Zn-1Y-0.6Zr alloys were prepared by rapidly solidified method.Solidification structure and properties of the prepared alloy were investigated by XRD

SEM

HRTEM and micro-hardness measurements.Microstructure of the alloy is composed of fine α-Mg phase

amorphous phases and I-Mg3Zn6Y quasicrystal phase discontinuously distributes along crystal boundary.Based on the heat transfer theory

the cooling rate of the alloy ribbons can be calculated by one-dimensional heat conductivity equation.With the increase of cooling rate

grain size in the microstructure of the alloy is refined with the more homogeneous distribution of composition

and the volumetric fractions of amorphous phase are raised

meanwhile

micro-hardness value of the alloy is increased greatly

and the maximum value reaches Hv 167

which is 2.2 times of that of the conventionally solidified alloy.

关键词

冷却速度快速凝固Mg-5Zn-1Y-0.6Zr合金显微组织

Keywords

Cooling RateRapid SolidificationMg-5Zn-1Y-0.6Zr AlloyMicrostructure

references

Alert me when the article has been cited

提交

Structure of Rapidly Solidified Al-Zr-Ti Alloy

Microstructure of Rapidly-solidified Ti-Ni-Cu Shape Memory Alloy Ribbons

Microstructure of Rapidly Solidified Cu₈₃Fe₁₇ Alloys

Electromigration Behavior of Cu/Sn-58Bi/Cu Solder Joints

Effects of Cooling Rate on Solidification Characteristics and Microstructure of Al-Fe Alloy