Comparison Analysis of Temperature Variation between Suction Casting A356-5SiC<sub>p</sub> Composites and A356 Alloy

Zhao Yu; Zhao Haidong; Dong Puyun

Views : 0 下载量: 96 CSCD: 2

Export
Share
Collection
Album

Comparison Analysis of Temperature Variation between Suction Casting A356-5SiC_p Composites and A356 Alloy
Vol. 31, Issue 8, Pages: 753-756(2011)
Published： 2011 ，
DOI：

扫描看全文

[1]赵宇,赵海东,董普云.A356-5SiC_p和A356吸铸温度变化的对比分析[J].特种铸造及有色合金,2011,31(08):753-756.

Zhao Yu, Zhao Haidong, Dong Puyun. Comparison Analysis of Temperature Variation between Suction Casting A356-5SiC_p Composites and A356 Alloy. [J]. Special Casting & Nonferrous Alloys 31(8):753-756(2011)
[1]赵宇,赵海东,董普云.A356-5SiC_p和A356吸铸温度变化的对比分析[J].特种铸造及有色合金,2011,31(08):753-756. DOI：

Zhao Yu, Zhao Haidong, Dong Puyun. Comparison Analysis of Temperature Variation between Suction Casting A356-5SiC_p Composites and A356 Alloy. [J]. Special Casting & Nonferrous Alloys 31(8):753-756(2011) DOI：

摘要

对体积分数为5%的SiC颗粒增强的A356复合材料和A356合金分别进行吸铸试验

测量熔体充型与凝固过程中铸件和铸型的温度

讨论了SiCp/A356复合材料与A356合金的铸件和铸型的温度变化规律。结果表明

SiCp的加入使SiCp/A356复合材料凝固前温度下降速度增大

凝固后的温度下降速度减小;同时由于潜热不同

SiCp/A356复合材料结晶温度低于A356合金。

Abstract

Suction casting SiCp/A356 metal matrix composites（MMCs）with 5% reinforced particles and A356 alloy were carried out

respectively.Temperature of castings and mould during filling and solidification process was measured to discuss the temperature variation of SiCp/A356 composites and A356 alloy castings and their moulds.The results show that SiCp addition can increase the temperature-decrement rate of SiCp/A356 composites before solidification and decrease the temperature-decrement rate after solidification.In addition

due to the difference of latent heat between the composites and the matrix alloy

the solidification transformation temperature of SiCp/A356 composites is lower than that of A356 alloy.

关键词

SiCp/A356温度吸铸凝固

Keywords

SiCp/A356 CompositesTemperatureSuction CastingsSolidification

references

Alert me when the article has been cited

提交

Effects of Upward Continuous Casting Parameters on Solidification Behavior of Oxygen-free Copper Billets

The Effect of the Pressure and Chills on the Solidification of Thin-Section and Complicated Aluminium Casting with Plaster Mold in Counter-Pressure Casting

Numerical Simulation for Solidification in Horizontal Continuous Casting

The Influence of Solar Eclipse on the Solidification of Pb-Sn Alloy

Comparison Analysis of Temperature Variation between Suction Casting A356-5SiCp Composites and A356 Alloy

DOI：

摘要

Abstract

关键词

Keywords

references

Comparison Analysis of Temperature Variation between Suction Casting A356-5SiC_p Composites and A356 Alloy