Squeezing Casting Aluminum Alloy Door Inner Panel for Automobile

Liu Zelin; Li Luoxing; Wang Shuiping; Zhu Biwu; Wang Yang

切换中文

Views : 41 Downloads: 213 CSCD: 1

Export
Share with wechat friends or circle of friends

Share
Collection
Album

Squeezing Casting Aluminum Alloy Door Inner Panel for Automobile
- role： First author 第一作者
- Affiliation：
  State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body,College of Materials Science and Engineering,Hunan University
Liu Zelin
1 2 ,
- Affiliation：
  State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body,College of Materials Science and Engineering,Hunan University
Li Luoxing
1 2 ,
- Affiliation：
  State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body,College of Materials Science and Engineering,Hunan University
Wang Shuiping
1 2 ,
- Affiliation：
  State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body,College of Materials Science and Engineering,Hunan University
Zhu Biwu
1 2 ,
- Affiliation：
  State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body,College of Materials Science and Engineering,Hunan University
Wang Yang
1 2
Vol. 31, Issue 9, Pages: 824-827(2011)
Published： 2011 ，
DOI：

Scan for full text

Quote
[1]刘泽林,李落星,王水平,朱必武,王洋.铝合金车门内板挤压铸造工艺研究[J].特种铸造及有色合金,2011,31(09):824-827.

Liu Zelin, Li Luoxing, Wang Shuiping, et al. Squeezing Casting Aluminum Alloy Door Inner Panel for Automobile. [J]. Special Casting & Nonferrous Alloys 31(9):824-827(2011)
[1]刘泽林,李落星,王水平,朱必武,王洋.铝合金车门内板挤压铸造工艺研究[J].特种铸造及有色合金,2011,31(09):824-827. DOI：

Liu Zelin, Li Luoxing, Wang Shuiping, et al. Squeezing Casting Aluminum Alloy Door Inner Panel for Automobile. [J]. Special Casting & Nonferrous Alloys 31(9):824-827(2011) DOI：

Abstract

Effects of processing parameters on mechanical properties of squeezing casting ADC12 alloy were investigated.Through simulating squeezing casting process of door inner panel with the help of a CAE software,distribution of temperature field during filling process was presented at different pouring temperatures and mold temperatures.Based on the simulation results,two sets of processing parameters were designed to squeeze door inner panel for automobile,and door inner panel was produced successfully.Evaluation of aluminum panel quality was carried out in term of tensile testing,metallographic observation,environmental scanning electron microscope（ESEM） and auger electron spectrometry.It is found that the door inner panel with a relatively high mechanical properties and good surface quality as well as fine quiaxed primary Al phase can be obtained with pouring at 730 ℃ and pressure of 27 MPa as well as mold temperature of 310 ℃.

transl

Keywords

Squeezing Casting; Aluminum Alloy Door Inner Panel; Al-Si Alloy; Mechanical Properties; Microstructure

transl

摘要

研究了工艺参数对挤压铸造ADC12合金力学性能的影响。通过对车门内板挤压铸造过程进行仿真分析

得出了不同浇注温度和模具温度下充型过程中的温度场分布。并据此设计了两组不同参数对工艺车门内板进行挤压铸造

并完成了产品的试制。通过拉伸试验、金相组织及能谱分析对铸件质量进行了评价。对比分析表明

在浇注温度为730℃、模具温度为310℃、压力为27MPa条件下

得到了α铝基体为细小等轴晶、力学性能和表面质量良好的铸件。

Abstract

distribution of temperature field during filling process was presented at different pouring temperatures and mold temperatures.Based on the simulation results

two sets of processing parameters were designed to squeeze door inner panel for automobile

and door inner panel was produced successfully.Evaluation of aluminum panel quality was carried out in term of tensile testing

metallographic observation

environmental scanning electron microscope（ESEM） and auger electron spectrometry.It is found that the door inner panel with a relatively high mechanical properties and good surface quality as well as fine quiaxed primary Al phase can be obtained with pouring at 730 ℃ and pressure of 27 MPa as well as mold temperature of 310 ℃.

关键词

挤压铸造铝合金车门内板铝硅合金力学性能微观组织

Keywords

Squeezing CastingAluminum Alloy Door Inner PanelAl-Si AlloyMechanical PropertiesMicrostructure

references

Alert me when the article has been cited

Submit

Effects of Sn，Ca Addition on Microstructure and Properties of Squeezing Casting Mg-Sn-Ca Alloy

Comparison of Mechanical Properties of ADC12 Aluminum Alloy Connecting Rod Cap Produced by Die Casting and by Squeezing Casting

Effects of RE on Microstructure and Mechanical Properties of Squeeze Cast AlSi7Cu4MgMn Alloy

Effects of Single/Double Size SiC_p on Microstructure and Properties of AZ91D Alloy

Effects of Casting Process on Structure and Mechanical Properties of Mg-12Zn-1Y Alloy

Related Author

Qin Jian 华中科技大学材料成形与模具技术全国重点实验室

Zhao Dijia 华中科技大学材料成形与模具技术全国重点实验室

Chen Lu 华中科技大学材料成形与模具技术全国重点实验室

Li Jianyu 华中科技大学材料成形与模具技术全国重点实验室

Pan Yu 华中科技大学材料成形与模具技术全国重点实验室

Wu Shusen 华中科技大学材料成形与模具技术全国重点实验室

Guo Wei 华中科技大学材料成形与模具技术全国重点实验室

Lü Shulin 华中科技大学材料成形与模具技术全国重点实验室

Related Institution

State Key Laboratory of Materials Forming and Die & Mould Technology，Huazhong University of Science and Technology

College of Mechanical Engineering,Chongqing Technology and Business University

School of Materials Science and Engineering,Harbin Institute of Technology

School of Mechatronics Engineering,Harbin Institute of Technology

Department of Mechanical Engineering,Taiyuan Institute of Technology

⁰